SUMMARY: 280R with additional qlogic HBA
2007-12-25 1:13:00
Thanks Jeff and others who might answer.
Anshuman Kanwar
Unix SysAdmin
Expertcity Inc.
--
(805) 690-5714 [off] ansh at expertcity.com
(805) 895-4231 [cel] 5385 Hollister Ave
(805) 690-6471 [fax] Goleta, CA. 93111
> -----Original Message-----
> From: Jeff Horwitz [mailto:jhorwitz75 at yahoo.com]
> Sent: Thursday, May 08, 2003 3:28 PM
> To: Anshuman Kanwar
> Subject: RE: 280R with additional qlogic HBA
>
>
> the isp2100's are not supported on the ultrasparc-iii
> platform. you'll
> probably find a message stating this if you run 'dmesg'. you have to
> upgrade to an isp2200 based model.
>
> -jeff
>
> -----Original Message-----
> From: codeprof-bounces at codeprof.com
> [mailto:codeprof-bounces at codeprof.com]On Behalf Of
> Anshuman Kanwar
> Sent: Thursday, May 08, 2003 6:16 PM
> To: 'codeprof at codeprof.com'
> Subject: 280R with additional qlogic HBA
>
>
> Hi Managers,
> I am trying to connect a qlogic (ISP2100A) based HBA ( PCI
> to FCAL) on a
> 280R. running Solaris 5.9.
>
> 1) The card is plugged into PCI 1 slot, which is the only
> 66MHz PCI slot.
> 2) the other end of the fiber is connected to a A5200 running
> in split mode.
> Plan is to connect 2 280-R's to two halves of the A5200.
> 3) The A5200 shows no signal on its GBIX.
> 4) I ran devfsadm -v but no devices were detected
>
> 5) prtdiag shows
> ========================= IO Cards =========================
>
>
> Bus Max
> IO Port Bus Freq Bus Dev,
> Brd Type ID Side Slot MHz Freq Func State Name
> Model
> ---- ---- ---- ---- ---- ---- ---- ---- -----
> -------------------------------- ----------------------
> I/O PCI 8 B 2 33 33 3,0 ok
> pci108e,1000-pci108e,1000.1
>
> I/O PCI 8 B 2 33 33 3,1 ok SUNW,hme-pci108e,1001
> SUNW,qsi-cheerio
> I/O PCI 8 A 1 33 66 1,0 ok
> scsi-pci1077,2100.1077.1.4
>
> The 3rd entry seems to be the qlogic card but the corresp.
> QLC entries never
> show up.
>
> 6) I've checked all relavent drivers are installed.
>
> i.e SUNW-
> fcp
> fcpx
> ifp
> ifpx
> qlc
> qlcx
> usoc
> usocx
>
>
> If I try to plug in the same card into a e420 instead of the
> 280, the whole
> setup works beautifully.
>
> Only difference I can think of is that the 280 has FC drives
> internally as
> opossed to the 420.
>
> What am I missing ?
>
>
> Thanks,
> -Ansh
> _______________________________________________
> codeprof mailing list
> codeprof at codeprof.com
> http://www.codeprof.com/execute/ask/?codeinfoid=22827
Comments
Got something to say?
You must be logged in to post a comment.
